Renault Samsung Air Conditioner Filter Replacement Method Real

(1)Basic supplies are flat-headed screwdriver or Hera T20 star wrench 10mm socket wrench cabin filter new
(2)On top of that, you should prepare items for knee shock relief such as matsMy Crucible is precious
(3)Imochen Village
(4)I’ll set it up like thisOf course, you don’t have to. It’s not my knees
(5)a model village
(6)Remove the driver’s mat
(7)Imo-haeng Village
(8)Remove the interior material next to the accelerator pedalPut your hand underneath and pull it
(9)That’s where the cabins filter are sleeping
(10)Looking at the picture again, I’m about to curse again
(11)I think it’s the creative spirit of car makers
(12)Why on earth
(13)Usually, it can be easily exchanged in a glove box
(14)This model village
(15)Remove the interior material on the door with a straight screwdriver or Hera
(16)You just have to put it in the gap
(17)Next, below the driver’s seat
(18)The 10mm bolt holding the gas inlet and the engine hood lever must be released
(19)Pull the interior materials under the steering to remove them
(20)You can pull it to the driver’s seat
(21)Don’t worry about breaking it!
(22)Imorang Village
(23)Then, pull the equipment towards the inner wheel seat under the steering to remove it
(24)It’s supposed to take out all the wiresThen, it’s good for your personal health to get bigger
(25)I’m just working on it
(26)In this work, a decent curiosity and a spirit of challenge are detrimental
(27)If you look inside, there’s another bolt on the side where the gas pump and engine hood lever are installed
(28)This bolt loosens the undercover
(29)Use a 20T star wrench
(30)a village of Imohan
(31)Now, I’m going to remove the undercover
(32)It’s going to be a beach
(33)It’s not one bolt, it’s two bolts
(34)There’s one more on the right
(35)This is the undercover
(36)You can grab it and pull it outIf you want to make it easier to work later, just cut the accelerator pedal part under the rope saw, and it will be easier next timeIt can be exchanged immediately after removalI don’t want to do undercover
(37)Dragon
(38)Inside the accelerator pedal
(39)I took it out
(40)Now I kneel down with a polite prayerThen, if you want to move your body to the place where the cabin filter is, you should remove the device that’s blocking the cover
(41)Here we go
(42)It’s good
(43)I’ll bow to you, but it’s also annoying, and I decide whether the wind direction won’t change if I put it in the wrong way and go on my career pathShaving the storage wind scent
(44)You can just ride it
(45)I did it
(46)Remove the cover
(47)There’s a clasp at the bottom. It’s supposed to be pressed up
(48)It’s the moment to meet you

(1)This model village
(2)I’m going to catch him and take him out. I’m angry
(3)the village of Imotep
(4)This is a comparison between waste filter and new filterYou need to do this to make it look better
(5)the village of Imotep
(6)I took a sneak peek at the habitat
(7)Of course, it’s impossible to check with the naked eye, so I put the camera in
(8)The right side is an evaporator, and when mold forms here, the air conditioner smellsBut what are those little dusts and fallen leaves
(9)I used a dusting spray to shake it off
(10)The only thing left is to install a new filter
(11)In order to maximize the performance of the cabin filter, one must look closely at the direction of the airflow written on the filterThe method of labeling filters that come out as genuine parts of Renault Samsung and filters sold in the aftermarket are differentThe genuine parts filter is fitted with an arrow pointing towards the engine, and for the aftermarket, the arrow is pointing towards the driver’s seat as shown in the picture
(12)watchful
(13)I’ll put it on
(14)Don’t be this model
(15)From now on, the fight begins in earnest
(16)need a knack
(17)Remember, the filter is elastic, so even if it crumples a little, it spreads out when it goes inside
(18)Only by using this nature can we reduce the amount of rough language that comes out in our mouths
(19)The first trick is to crumple a little bit and put the bottom and top into the hole
(20)Then, push the bottom a little bit and push the top a little bit and repeat
(21)If you do that, you’ll end up going in right away
(22)It’s very difficult to explain in writing
(23)If it’s installed, as usual, assemble it in reverse order to complete